HPE PROLIANT MICROSERVER GEN10 PLUS

HPE PROLIANT MICROSERVER GEN10 PLUS

HPE ProLiant MicroServer Gen10 Plus delivers an affordable compact yet powerful entry level server that you can customize for onpremises, hybrid cloud or even workloads demanding datacenter performance.

Standard Features

Processor

Intel® Xeon® E Processor is designed to deliver the best combination of performance, built-in capabilities, and cost-effectiveness.
This product also supports Intel® Pentium® processors.

Choose one of the following processors based on the model:

Intel Xeon E-2200 Series / 9th Gen Pentium G
Model	CPU Frequency	Cores	L3 Cache	Power	DDR4	SGX
Xeon E-2224	3.4 GHz	4	8 MB	71W	2666 MT/s	No
Pentium G5420	3.8 GHz	2	4 MB	54W	2400 MT/s	No

Chipset

Intel® C242 Chipset

Memory

Type

HPE Standard Memory

DDR4 Unbuffered (UDIMM)

DIMM Slots Available

Maximum Capacity

32GB (2 x 16GB UDIMM @2666 MT/s)

Notes: The maximum memory speed depends on processor model.

Memory Protection

Network Controller

Embedded Intel i350 AM41Gb 4-port network controller
The HPE ProLiant MicroServer Gen10 Plus server offers the customer a 4-port NIC standard with the option to upgrade with a variety of networking options.

Expansion Slots

ExpansionSlot #

Technology

Bus Width**

Connector Width

Form Factor

Notes

PCIe 3.0

x 16

Low Profile

Supported on the

PCIe Riser Board

Storage Control

The Gen10 controller naming framework has been updated to simplify identification as depicted below. For a more detailed breakout of the available Gen10 Smart Array controllers visit the HPE Smart Array Gen10 Controllers Data Sheet.

Software RAID

HPE Smart Array S100i SR Gen10 Software RAID

Notes:

− HPE Smart Array S100i SR Gen10 SW RAID will operate in UEFI mode only. For legacy support an additional controller will be needed

− The S100i only supports Windows. For Linux users, HPE offers a solution that uses in-distro open-source software to create a two-disk RAID 1 boot volume. For more information visit: https://downloads.linux.hpe.com/SDR/project/lsrrb/

Essential RAID Controller

HPE Smart Array E208i-p SR Gen10 Controller

Internal Storage Devices

Hard Drives (None ship standard)
Solid State Drives (None ship standard)

Maximum Internal Storage

Non-hot plug SATA

16TB (4 x 4TB) 3.5″ SATA HDD

960GB (4x 240GB) 2.5” SATA SSD

Notes: The maximum storage indicated is aligned with the current HDD & SSD option list supported. Maximum internal storage supported would change with the server’s option support plan.

Interfaces

Video	1 Rear VGA port 1 Rear DisplayPort 1.1a
USB 2.0 Type-A Ports	1 total (1 internal)
USB 3.2 Gen1 Type-A Ports	4 total (4 rear)
USB 3.2 Gen2 Type-A Ports	2 total (2 front)
Network RJ-45 (Ethernet)	4

Server Power Cords

All pre-configured models ship standard with one or more country-specific 6 ft/1.83m C5 power cords depending on models. If a different power cord is required, please check the HPE Power Cords and Cables web page.

Power Supply

One (1) 180 Watts , non-redundant External Power Adapter

Form Factor

Ultra Micro Tower

System Fans

One (1) non-redundant system fan shipped standard

Industry Standard Compliance

ACPI V6.1 Compliant
PCIe 3.0 Compliant
PXE Support
WOL Support
EMC Class B
Microsoft® Logo certifications
VGA Port
DP 1.1a
SMBIOS 3.1
UEFI 2.6
Redfish API
IPMI 2.0
Advanced Encryption Standard (AES)
Triple Data Encryption Standard (3DES)
SNMP v3
TLS 1.2
DMTF Systems Management Architecture for Server Hardware Command Line Protocol (SMASH CLP)
Active Directory v1.0
ASHRAE A2
UEFI (Unified Extensible Firmware Interface Forum)
USB 2.0 Compliant
USB 3.2 Compliant
SATA 6Gb/s

HPE PROLIANT MICROSERVER GEN10 PLUS

Related products